BMW K100

  I, like many bikers, had the idea of one day doing a project bike. Every bike I’ve owned has been modified to my personal taste, this is my K1200R which was dead stock when I got it.

K1200R

I had talked about wanting to do a proper build for some time. My very supportive, beautiful wife asked me what I was waiting for? I stumbled across the following bike on the BIKEEXIF and got motivated!

Robock K100

I was blown away that a K100 could look so good! This blog is how, over 4 months, I turned this;

image

Into this.

Dark Profile

And after my mate crashed it, this.

BMW K100 Rebuild (9)

I found the donor bike in Adelaide as an unregistered trade-in advertised on gumtree. My Dad and I did a quick 1540km round trip, and the real journey began!

BMW K100 Project (22)

Bought a bike lift off ebay.

Digital StillCamera

Fairings and seat were stripped and sold to a wrecker for $450, No turning back now!

Digital StillCamera

Being my first build, I’m still trying to work out the sequence of work. It is a bit daunting! I decided to start easy and do the front guard. K100 Project (16)

I marked out trimmed shape I wanted

K100 Project (17)

and went at it with the dremel.

K100 Project (18)

Have ordered 3M carbon fibre wrap to finish it off.

Dad did a good job of trimming unwanted metal tags from the subframe

K100 Project (26)

I took a slightly different route for a radiator overflow tank!

K100 Project (37)

Pace should pick up now, the goodies that arrived this week; Rear sets from BSK SpeedWorks Speedo from Daktota Digital

The rear-sets were an easy fit, and very well made

Before

K100 Project (40)

After

K100 Project (42)

I was hoping the exhaust collector I found would be easy to rotate 90 degrees to get the angle I wanted. Not possible! It will only fit in the header pipes one way.

IMG_0867 IMG_0868 IMG_0869

Have found Mick at Valley Engineering, who has modified it to suit.

IMG_088520130728-161122.jpg

He also has fixed the Clip-On bars, making the bars 22mm and the mounts 41.3mm. I’m getting a rough idea of the seat unit style I’m after. I want to follow the line from the fuel tank base through to the rear tail unit. I’m not after a particular style, but aiming for a look that is a cross between café racer and street fighter.

Seat Unit Idea

Clip-ons were an easy fit after mods to the bar diameter and fork clamp!

IMG_0893 IMG_0894

The Speedo mount is done. Longer brake hose fitted.

IMG_0900

Lowered the speedo a bit, happy with it now

IMG_0910 IMG_0911

Decided to only use one horn. Made a bracket and mounted it on the left, behind the radiator.

IMG_0912

Rear brake reservoir mounted.

BMW K100 Project (79)

Getting rid of the last of the frame tags.

BMW K100 Project (77)

Bike is now off to Valley Engineering for some surgery.

IMG_0927

IMG_0929

Mick (on the right) is going to do the tasks I can’t do at home.

– Hone out the hole in the upper triple clamp to hold the ignition block.

– Fabricate an exhaust hanger.

– Cut and brace the sub-frame.

– Manufacture the seat unit and tail piece.

Mick has form, turning his Ducati Monster SP into a café racer with the radiator moved to under the sub-frame!

One week later …………………………………………………..

BMW K100 Project (84) BMW K100 Project (85) BMW K100 Project (86)

Extra bracing of the sub-frame.

BMW K100 Project (87)

The smaller battery is now enclosed.

BMW K100 Project (88)

The ignition now fits in the clamp,

BMW K100 Project (89)

The seat unit is just how I wanted it. It continues the line from the tank, and the frame.

BMW K100 Project (90)

Fortunately, I provided accurate drawings, and a scale mock up to work from!

Seat Unit Idea BMW K100 Project (70)

The exhaust is now finished!

BMW K100 Project (91)

The tank and seat unit are off again for painting. My mate Pete of Peter’s Panels has offered to do the job for a couple of bottles of scotch! On the condition I do the preparation work. The colour is from a new range called ‘vibrance’. It is a nod to the BMW 1970’s colours, but with metal flake.

BMW K100 Project (92) BMW K100 Project (93) BMW K100 Project (94)

I bought some bar end indicators off eBay to use in the frame holes. Internal wiring was an interesting job!

BMW K100 Project (95) BMW K100 Project (96)

Front fender now covered with 3M carbon fibre wrap.

BMW K100 Project (97)

Battery connected and installed in custom made box.

IMG_0957.JPG (2)

Now for the part I’ve been dreading!

IMG_0960.JPG (2)

We have ignition!

IMG_0962.JPG (2)

I’ve managed to get most of the cautions working, I can’t get the neutral light working for some reason. I need the tank and seat unit back to run the engine to check tacho. Then to see if the OEM speedo signal will work………  nope!

I ended up getting a sensor unit from Dakota Digital and mounting it on the front wheel. It counts the wheel studs.

K100 Project (78a)

The master at work, putting on the base silver coat.

K100 Project (79)

The paint job by Pete is flawless!

20130914-135651.jpg 20130914-135720.jpg

The wiring is coming along. Yellow spaghetti! Thank you self closing braided line!

IMG_0983IMG_0982.JPG (2)

I’m away for work the next week, will book in the seat fabricator when I return. Reassembled to get the seat done.

20130922-192439.jpg K100 Project (87) K100 Project (88)

Got the seat back, great job! Put the bike together and added the headlight to preview the finished bike.

K100 Project (89) K100 Project (91) K100 Project (92) K100 Project (93)

After 6 days work, back into the wiring. This is a boring picture, but it is satisfying to get it right. Now have a waterproof quick release connector  for easy seat removal. IMG_1050.JPG (2)

I later changed to a smaller, completely waterproof connector.

K100 Project (95a)

I took the tank and seat back to Pete for a final touch up today. Pete surprised me with a sticker he’d got made up. It turns out the colour I chose is called “hornet orange”. Since I flew hornets in the RAAF, Pete had the sticker made. The bike now has a name!

IMG_0142

I’m now just waiting on a couple of 12ohm resistors from eBay. They need to be installed next to the flasher unit under the tank so the LED indicators work properly. While waiting I’ve changed the oil, oil filter, fuel filter, bled the brakes, and done some polishing.

IMG_1057.JPG (2)

I’ve got the indicators working, tank and seat back on. Given it a start up. Almost done!

K100 Project (98)K100 Project (101)

After initial rough running and stalling (I think it was air in the lines due fuel filter change), it settled down and ran smoothly. The exhaust is surprisingly not much louder than stock! Programmed the gear indicator and calibrated the speedo. The weight loss was apparent from the first crank of throttle! It is a bit of a reach to the bars, but at 100km/h the weight comes off the wrists and it should be good for longer rides. I still have few things to do. The rear mud guard looks like it can be chopped into a small fly screen to cover the instrument wiring.

I have been a bit remiss by not acknowledging my co-builder, dad. He provided the workshop, tools, and lots of unwanted advice (some of which was useful)!

Digital StillCamera

I did not like that the speedo wiring was visible (even though it was covered in black shrink wrap). The removed rear mud guard was made of plastic. I thought it looked about the right width. Cut to shape, then covered it in carbon fibre wrap. No more visible wires and cables!

IMG_1102 IMG_1100 IMG_1099

I also took off the centre stand to tidy up under the bike.

IMG_1103

The rear shock was on it’s last legs. Bit the bullet and installed a Hyperpro.

IMG_1104 IMG_1105

I took the bike to get the shock dialled in. Bad news is that it has lost so much weight I need a lighter spring! Going to get it resprung and revalved for the new weight.

Couldn’t only do the rear, so the forks are off for some White Power springs and oil change.

K100 Project (111)

New springs and oil. I think I can now say it is finished! Cleaned up and ready to go.

IMG_1130 IMG_1129 IMG_1128

I had been working towards entering it in a bike show in Melbourne called “Oil Stained Brain”. It turned out it did not make the cut, and I only finished it 2 days before the show. The weekend of the show, without a decent test ride, I took it on 1000km loop into the snowy mountains with some mates! The only glitch was having to tighten the folding mirrors when they folded back at 170km/h! DCIM100GOPRO  gopro captures (5)gopro captures (1) gopro captures (8)Double Hump (5)Double Hump (7)

After the loss of weight, and suspension work, it was as fast as my K1200R in the tight stuff! I’m still tinkering. Was not happy with the quality of the mirrors, so have changed to these. K100 Project (115)

I finally took some photos with a real camera (instead of my phone).

Tank Paint Speedo Seat Rearset Left  Profile Right Profile Left1 Indicator   K100 Project (162) K100 Project (163) K100 Project (164) K100 Project (161)

I have found the rear indicators not bright enough in direct sunlight. Santa made a late delivery of these beauties! K100 Project (165) K100 Project (166)

Definitely bright enough!

The baby bottle idea for the radiator overflow turned out to have insufficient volume. I have replaced it with a 500ml stainless steel drink bottle. photo

The join between the steel collector and the aluminium exhaust has never been ideal, continually working loose due to different expansion rates. I think I now have a solution using a V-clamp. It also makes for easy exhaust removal (needed to remove rear wheel).

K100 Project (169)

I took the opportunity to paint the header pipes black. The paint needed baking, so I used the BBQ. K100 Project (168)

All done!

K100 Project (170)

I will take it on a decent test ride as the Hornet is going to Tasmania for a 7 day extravaganza the end of Feb!

The seat pan is attached to the frame by two pins at he rear, and one central bolt at the front. I have occasionally noticed a small amount of seat pan flex, which I have decided to fix. I found these plastic lugs in the cupboard (I can’t remember where they came from).

K100 Project (171)

I drilled the centers so they would fit snugly onto the alan head bolts that hold the rear tank mount. I had to shape the tops to match the seat pan, then paint them black. K100 Project (172)

Rock solid now, ready for Tassie!

K100 Project (173)

Day three of riding the great roads of Tasmania, my mate Kev lost the front end under brakes. The resulting low side caused too much to continue. Tank, engine casing, foot pegs, gear shift, left bar and switch block. I thought I had finished this blog, I guess not!

IMG_1331 IMG_1332 IMG_1333 IMG_1334 IMG_1335

Shannons Insurance were great in getting it home, after several stressful hours when they were threatening to write it off and leave it in Tasmania!……………………

After recovering the bike to Melbourne, the Shannons assessor decided  my poor bike was a write-off!

The good news is I’m going to fix it myself. I’ll take the opportunity to do some upgrades, stay tuned!! I’ve got my bike back in the workshop, build number 2 can commence!

THE HORNET MACH II

I considered repairing the bike back to pre-crash condition, but it seemed a waste of money and effort to do all the work and end with the same bike. Having learned so much in the first build, I thought about what I could improve. The bike was a weapon in the corners, but I never had much faith in the tires (Kev, even less so now!). To run radial rubber, wider wheels are needed. A K1100 wheel bolts easily onto the rear. I know it is possible to bolt on a K1100 front end, which gives  4 spot calipers. I thought, but why take the front end 5 years into the future, why not 20 years? Old bikes with USD forks also look the biz!! IMG_1348

I’ve sourced some parts. Found a decent tank for $150.

IMG_1346

The Valve cover will require bead blasting.

IMG_1339 IMG_1353

I spent several hours at the wreckers looking for some USD forks in good condition. I needed a 3 spoke front wheel to match a K1100 rear wheel. The best solution was from a 2000 Yamaha R1. I put a deposit on the front end so I could take the triple clamps. I wanted to see if it was going to work before I paid the full amount!… I’ve got the triple clamps at Valley Engineering getting assessed for the transplant! The BMW post needs to be mated to the Yamaha clamps. If the R1 plan doesn’t work, I’ve sourced a BMW K1100 front end. In either case, I will need another solution to for the ignition key mount. I’ve decided to remove it from the triple clamp to clean  up the dash. I was scratching my head for a mounting solution when I spied the surviving mirror from the crash…. IMG_1355

Angle grinder and drill converted it to an ideal bracket for side mounting the ignition block! IMG_1356 IMG_1358

The R1 clamps are now fitted to the BMW shaft. Not cheap, but bolted up perfectly! Will now collect the rest of the front end and see how it fits. IMG_1361   IMG_1362 IMG_1364

Like a glove!

IMG_1363

Collected the engine covers after cleaning by sand rolling at Competition Coatings. He did the valve cover for free, to see if I liked the finish!

IMG_1365

The new rear-sets have arrived, slightly redesigned, now with knurled levers instead of rubber. Nice!

K100 Project (192)

I’ve used an angle grinder to remove the ignition mount and other tag from top triple clamp.

K100 Project (193)

Will use a bench grinder to tidy it up….. All done, and sent to get powder coated.

K100 Project (194)

The exhaust system is back after being ceramic coated front to back!

K100 Project (195) K100 Project (197)

I’ll leave the can off for now, as the new wheel is still getting painted. The wheels are back from the paint shop. BMW K1100 rear,  Yamaha R1 front, shod in Pirelli Angel GT tires.

K100 Project (198)

Lisa, trying to distract me from those sexy wheels!

IMG_1389

The rear bolted on no problem. Good clearance on both sides.

K100 Project (199)

I used the damaged rear-set plate to fabricate the speedo mount. I had a small altercation with the bench grinder during the process!

K100 Project (200)

Good result though, wanted it flush with top clamp.

K100 Project (201) K100 Project (202)

Have decided to change the headlight to the MT-03 unit.

K100 Project (203)  K100 Project (205)

I like it, but will have to see bike complete to be sure.

A whole new throttle quadrant was required. The K100 master cylinder is 13mm in diameter. This is OK for the original brakes, but would struggle to operate the R1 calipers. A K1100 (20mm) master cylinder is up to the task, but can only be fitted by replacing the whole quadrant. This necessitated a throttle cable change also.

I was going to re-route the front brake line to keep the top clamp clean, but I like the K100 design.

K100 Project (204)

The bar controls all done, just need to get some brake hoses fabricated.

K100 Project (206)K100 Project (207)

I had to modify the K1100 hubcap to fit the K100 hub. Found the carbon fiber badge on eBay.

K100 Project (208)

A rat tail file allowed the headlight bracket to take the indicators.

K100 Project (211)

The front end is now complete!

K100 Project (209)

I got the tank and seat from the paint shop today. The paintwork is exceptional!!

K100 Project (210)

The fuel pump mount was broken in the old tank. A new part tomorrow, then final assembly……..

K100 Project (212)

I was concerned the modern front end might not flow visually into the rest of the bike, but I couldn’t be happier!

K100 Project (224) K100 Project (213) K100 Project (221) K100 Project (220) K100 Project (219) K100 Project (218)  K100 Project (214)

I used the remains of the bent gear shift as a stopper so the stand doesn’t hit the  exhaust.

K100 Project (228) DSC_3820

I took the bike for it’s first proper ride through the hills yesterday. With the new front end and Pirelli rubber, it now feels like a modern sports bike. It is much more planted to the road, and the brakes are now comparable to my K1200R. I can now say the blog is complete (17-05-2014). The rebuild took just under 2 months.

Thanks for checking it out! It has now featured on The Bike Shed,  twicePipeburn, and Silodrome.

I was also contacted by BMW Australia who featured it on their website, then I was incredibly stoked to have it feature on the international BMW Motorrad website!

K100 Project (240) K100 Project (239) K100 Project (238) K100 Project (237) K100 Project (236) K100 Project (234) K100 Project (233) K100 Project (232) K100 Project (231) K100 Project (230) K100 Project (229) K100 Project (227)

My bike was accepted into the 2014 Oil Stained Brain bike show.

K100 Project (247) K100 Project (249) K100 Project (250)

K100 Project (252)

I finally got around to weighing it!

It now weighs 215kg fully fueled. Stock bike is 249kg, so it has lost 34kg. Distribution is 51/49 front/rear.

On to the next project

UPDATE

I haven’t updated this post for a long time now. After 4 years of trouble free riding, I’m considering letting the Hornet go. If you are interested, drop me a message.

317 thoughts on “BMW K100

  1. Hi Paul, just wanted to say massive congrats mate she’s such a clean looking build. Awesome page with lots of helpful info, I’ve just purchased a 94 k1100LT to start my cafe dream in Melbourne and have already got a few good tips from here so thanks 🙂 One quick question I’ve been trying to find an answer on and you may know it is when you cut and shorten the rear loop did you need an engineers certificate for rwc in Vic? Thanks for any info you can provide in advance
    Cheers
    Scott

  2. Hey Paul.

    Any recommendations on electrics? Mainly, what to keep, what to get rid of and what to replace with?

    Love the hornet build. Looking to put a more modern front end on mine too.

    Thanks

    1. Hi Bonny, replacing the instruments is a bit of a pain. There is circuitry in the original housing for fuel level and neutral light that means you lose these features. If I were to do it again, I would do what I did Mitch the Kawasaki, and retire completely with Motogadget.

      1. Thanks.

        I found some posts of yours on the K100 forum. Taking your advise and going with the morogadget. Funnily enough the only speedo I like is the same Dakota speedo you’re using. I know I’m in for a world of pain with that one but I figured pairing the m-unit with the brotbox from Maru-labs might give me half a shot.
        Any tips on getting it configured would be great. I’ll order the Dakota sensor too.

      2. Hi Bonny,

        Sorry, forgot to reply. The Dakota should work easily with the m-unit. Best to draw a wiring diagram before you start. I did one for the Kawasaki which you can find in my blog.

        Paul

Leave a Reply to simon bell Cancel reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s